Set Up the Network Firewall

Now that you’ve set up your password manager, you can move on to setting up the Network Firewall. You should stay logged in to the Admin Workstation to access the Network Firewall’s web interface for configuration.

Unfortunately, due to the wide variety of firewalls that may be used, we do not provide specific instructions to cover every type or variation in software or hardware. However, if you have the necessary expertise, we provide abstract firewall rules that can be implemented with iptables, Cisco IOS etc. This guide is based on pfSense, and assumes your firewall hardware has at least three interfaces: WAN, LAN, and OPT1. For hardware, you can build your own network firewall (not covered in this guide) and install pfSense on it. For most installations, we recommend buying a dedicated firewall appliance with pfSense pre-installed, such as the one recommended in the Hardware Guide.

We currently recommend the pfSense SG-4860, which has 6 interfaces: WAN, LAN, OPT1, OPT2, OPT3 and OPT4. If your firewall only has 3 NICs (WAN, LAN, and OPT1), you will need to use a switch on the OPT1 interface to connect the Admin Workstation for the initial installation.

If you are new to pfSense or firewall management in general, we recommend the following resources:

If you’re using the recommended SG-4860 firewall, then you may find the following resources useful:

Before You Begin

First, consider how the firewall will be connected to the Internet. You will need to provision several unique subnets, which should not conflict with the network configuration on the WAN interface. If you are unsure, consult your local sysadmin.

Many firewalls, including the recommended Netgate pfSense, automatically set up the LAN interface on This particular private network is also a very common choice for home and office routers. If you are connecting the firewall to a router with the same subnet (common in a small office, home, or testing environment), you will probably be unable to connect to the network at first. However, you will be able to connect from the LAN to the pfSense WebGUI configuration wizard, and from there you will be able to configure the network so it is working correctly.

Configuring Your Firewall

If your firewall has at least 4 NICs, as the SG-4860 does, we will refer to the ports as WAN, LAN, OPT1, and OPT2. In this case, we can now use a dedicated port on the network firewall for each component of SecureDrop (Application Server, Monitor Server, and Admin Workstation), so you do not need a switch like you do for a 3-NIC configuration.

Depending on your network configuration, you should define the following values before continuing. For the examples in this guide, we have chosen:

  • Admin Subnet:
  • Admin Gateway:
  • Admin Workstation:
  • Application Subnet:
  • Application Gateway:
  • Application Server (OPT1):
  • Monitor Subnet:
  • Monitor Gateway:
  • Monitor Server (OPT2) :

Initial Configuration

Unpack the firewall, connect the power, and power on the device.

We will use the pfSense WebGUI to do the initial configuration of the network firewall. [1]

Connect to the pfSense WebGUI

  1. Boot the Admin Workstation into Tails from the Admin Live USB.

  2. Connect the Admin Workstation to the LAN interface. You should see a popup notification in Tails that says “Connection Established”. If you click on the network icon in the upper right of the Tails Desktop, you should see “Wired Connected”:

    Wired Connected


    Make sure your only active connection is the one you just established with the network firewall. If you are connected to another network at the same time (e.g. a wireless network), you may encounter problems trying to connect the pfSense WebGUI.

  3. Launch the Unsafe Browser from the menu bar: Applications ▸ Internet ▸ Unsafe Browser.

    Launching the Unsafe Browser


    The Unsafe Browser is, as the name suggests, unsafe (its traffic is not routed through Tor). However, it is the only option because Tails intentionally disables LAN access in the Tor Browser.

  4. A dialog will ask “Do you really want to launch the Unsafe Browser?”. Click Launch.

    You really want to launch the Unsafe Browser

  5. You will see a pop-up notification that says “Starting the Unsafe Browser…”

    Pop-up notification

  6. After a few seconds, the Unsafe Browser should launch. The window has a bright red border to remind you to be careful when using it. You should close it once you’re done configuring the firewall and use the Tor Browser for any other web browsing you might do on the Admin Workstation.

    Unsafe Browser Homepage

  7. Navigate to the pfSense WebGUI in the Unsafe Browser:


    If you have trouble connecting, go to your network settings and make sure that you have an IPv4 address in the range. You may need to turn on DHCP, else you can manually configure a static IPv4 address of 192.168.1.x with a subnet mask of However, make sure not to configure your Tails device to have the same IP as the firewall (

  8. The firewall uses a self-signed certificate, so you will see a “This Connection Is Untrusted” warning when you connect. This is expected. You can safely continue by clicking Advanced, Add Exception…, and Confirm Security Exception.

    Your Connection is Insecure

  9. You should see the login page for the pfSense GUI. Log in with the default username and passphrase (admin / pfsense).

    Default pfSense

Alternate Hostnames

Before you can set up the hardware firewall, you will need to set the Alternate Hostnames setting after logging in. You will see the Setup Wizard but you shoud exit out of it by navigating to System -> Advanced. In the Alternate Hostnames dialog box, add as well as the IP address of the Admin Gateway. If you decide against using our recommended defaults for the Admin Gateway, you should include that value here. After saving these settings you should be able to go back to System and select Setup Wizard.

Alternate Hostnames

Setup Wizard

  1. If you’re setting up a brand new (or recently factory reset) router, logging in to the pfSense WebGUI will automatically start the Setup Wizard. Click Next, then Next again. Don’t sign up for a pfSense Gold subscription (unless you want to).

  2. On the “General Information” page, we recommend leaving your hostname as the default (pfSense). There is no relevant domain for SecureDrop, so we recommend setting this to securedrop.local or something similar. Use your preferred DNS servers. If you don’t know what DNS servers to use, we recommend using Google’s DNS servers: and Click Next.

    pfSense General Info

  3. Leave the defaults for “Time Server Information”. Click Next.

  4. On “Configure WAN Interface”, enter the appropriate configuration for your network. Consult your local sysadmin if you are unsure what to enter here. For many environments, the default of DHCP will work and the rest of the fields can be left blank. Click Next.

  5. For “Configure LAN Interface”, use the IP address of the Admin Gateway ( and the subnet mask (/24) of the Admin Subnet. Click Next.

    Configure LAN Interface

  6. Set a strong admin passphrase. We recommend generating a strong passphrase with KeePassX, and saving it in the Tails Persistent folder using the provided KeePassX database template. Click Next.

  7. Click Reload. Once the reload completes and the web page refreshes, click the corresponding “here” link to “continue on to the pfSense webConfigurator”.

At this point, since you (probably) changed the LAN subnet settings from their defaults, you will no longer be able to connect after reloading the firewall and the next request will probably time out. This is not an error - the firewall has reloaded and is working correctly. To connect to the new LAN interface, unplug and reconnect your network cable to get a new network address assigned via DHCP. Note that if you used a subnet with fewer addresses than /24, the default DHCP configuration in pfSense may not work. In this case, you should assign the Admin Workstation a static IP address that is known to be in the subnet to continue.

Now the WebGUI will be available on the Admin Gateway address. Navigate to https://<Admin Gateway IP> in the Unsafe Browser, and login as before except with the new passphrase you just set for the pfSense WebGUI. Once you’ve logged in to the WebGUI, you are ready to continue configuring the firewall.

Connect Interfaces and Test

Now that the initial configuration is completed, you can connect the WAN port without potentially conflicting with the default LAN settings (as explained earlier). Connect the WAN port to the external network. You can watch the WAN entry in the Interfaces table on the pfSense WebGUI homepage to see as it changes from down (red arrow pointing down) to up (green arrow pointing up). This usually takes several seconds. The WAN’s IP address will be shown once it comes up.

Finally, test connectivity to make sure you are able to connect to the Internet through the WAN. The easiest way to do this is to use ping (Diagnostics → Ping in the WebGUI). Enter an external hostname or IP that you expect to be up (e.g. and click “Ping”.


Disable DHCP on the LAN

pfSense runs a DHCP server on the LAN interface by default. At this stage in the documentation, the Admin Workstation likely has an IP address assigned via that DHCP server.

In order to tighten the firewall rules as much as possible, we recommend disabling the DHCP server and assigning a static IP address to the Admin Workstation instead.

Disable DHCP Server On the Firewall

To disable DHCP, navigate to Services ▸ DHCP Server in the pfSense WebGUI. Uncheck the box labeled Enable DHCP server on LAN interface, scroll down, and click the Save button.

Disable DHCP

Assign a Static IP Address to the Admin Workstation

Now you will need to assign a static IP to the Admin Workstation.

You can easily check your current IP address by clicking the top right of the menu bar, clicking on the Wired Connection and then clicking Wired Settings.

Wired Settings

From here you can click on the cog in the lower right of the panel:

Tails Network Settings

This will take you to the network settings, where you can click IPv4 to see whether or not the Automatic (DHCP) or Manual (static IP) setting is turned on.

Change to the IPv4 Settings tab. Change Addresses from Automatic (DHCP) to Manual (if it isn’t already).

Fill in the static networking information for the Admin Workstation:

  • Address:
  • Netmask:
  • Gateway :

IPv4 Settings


The Unsafe Browser will not launch when using a manual network configuration if it does not have DNS servers configured. This is technically unnecessary for our use case because we are only using it to access IP addresses on the LAN, and do not need to resolve anything with DNS. Nonetheless, you should configure some DNS servers here so you can continue to use the Unsafe Browser to access the WebGUI in future sessions.

We recommend keeping it simple and using the same DNS servers that you used for the network firewall in the setup wizard.

Admin Workstation Static IP Configuration

Click Apply. If the network does not come up within 15 seconds or so, try disconnecting and reconnecting your network cable to trigger the change. You will need you have succeeded in connecting with your new static IP when you see a pop-up notification that says “Tor is ready. You can now access the Internet”.

Troubleshooting: DNS Servers and the Unsafe Browser

After saving the new network configuration, you may still encounter the “No DNS servers configured” error when trying to launch the Unsafe Browser. If you encounter this issue, you can resolve it by disconnecting from the network and then reconnecting, which causes the network configuration to be reloaded.

To do this, click the network icon in the system toolbar, and click Disconnect under the name of the currently active network connection, which is displayed in bold. After it disconnects, click the network icon again and click the name of the connection to reconnect. You should see a popup notification that says “Connection Established”, followed several seconds later by the “Tor is ready” popup notification.

For the next step, SecureDrop Configuration, you will manually configure the firewall for SecureDrop, using screenshots or XML templates as a reference.

SecureDrop Configuration

SecureDrop uses the firewall to achieve two primary goals:

  1. Isolating SecureDrop from the existing network, which may be compromised (especially if it is a venerable network in a large organization like a newsroom).
  2. Isolating the Application Server and the Monitor Server from each other as much as possible, to reduce attack surface.

In order to use the firewall to isolate the Application Server and the Monitor Server from each other, we need to connect them to separate interfaces, and then set up firewall rules that allow them to communicate.

Set Up OPT1

We set up the LAN interface during the initial configuration. We now need to set up the OPT1 interface for the Application Server. Start by connecting the Application Server to the OPT1 port. Then use the WebGUI to configure the OPT1 interface. Go to Interfaces ▸ OPT1, and check the box to Enable Interface. Use these settings:

  • IPv4 Configuration Type: Static IPv4
  • IPv4 Address: (Application Gateway IP)

Make sure that the CIDR routing prefix is correct (/24). Leave everything else as the default. Save and Apply Changes.


Set Up OPT2

Next, you will have to enable the OPT2 interface. Go to Interfaces ▸ OPT2, and check the box to Enable Interface. OPT2 interface is set up similarly to how we set up OPT1 in the previous section. Use these settings:

  • IPv4 Configuration Type: Static IPv4
  • IPv4 Address: (Monitor Gateway IP)

Make sure that the CIDR routing prefix is correct (/24). Leave everything else as the default. Save and Apply Changes.


Set Up the Firewall Rules

Since there are a variety of firewalls with different configuration interfaces and underlying sets of software, we cannot provide a set of network firewall rules to match every use case.

The easiest way to set up your firewall rules is to look at the screenshots of a correctly configured firewall and edit the interfaces, aliases, and firewall rules on your firewall to match them.

Use Screenshots of Firewall Configuration

Here are some example screenshots of a working pfSense firewall configuration. You will add the firewall rules until they match what is shown on the screenshots.

First, we will configure IP and port aliases. Navigate to Firewall ▸ Aliases and you should see a screen with no currently defined IP aliases:

Blank IP Aliases

Next you will click Add to add each IP alias. You should leave the Type as Host. Make aliases for the following:

  • admin_workstation:
  • app_server:
  • external_dns_servers:,
  • monitor_server:
  • local_servers: app_server, monitor_server

Add Firewall Alias

Click Save to add the alias.

Keep adding aliases until the screenshot matches what is shown here:

Firewall IP Aliases Pre Save

Finally, click Apply Changes. This will save your changes. You should see a message “The changes have been applied successfully”:

Firewall IP Aliases Post Save

Next click “Ports” for the port aliases, and add the following ports:

  • OSSEC: 1514
  • ossec_agent_auth: 1515

Your configuration should match this screenshot:

Port Aliases

Next we will configure firewall rules for each interface. Navigate to Firewall ▸ Rules to add firewall rules for the LAN, OPT1, and OPT2 interfaces.


Be sure not to delete the Anti-Lockout Rule on the LAN interface. Deleting this rule will lock you out of the pfSense WebGUI.

Add or remove rules until they match the following screenshots by clicking Add to add a rule.

LAN interface:

Firewall LAN Rules

OPT1 interface:

Firewall OPT1 Rules

OPT2 interface:

Firewall OPT2 Rules

Finally, click Apply Changes. This will save your changes. You should see a message “The changes have been applied successfully”. Once you’ve set up the firewall, exit the Unsafe Browser, and continue with the “Keeping pfSense up to date” section below.

Configuration Reference Templates

As an alternative to the provided screenshots, you can examine the provided .xml templates as a reference:

  • Interfaces config: install_files/network_firewall/interfaces-config-pfSense.xml
  • Aliases: install_files/network_firewall/aliases-config-pfSense.xml
  • Firewall rules: install_files/network_firewall/filter-config-pfSense.xml


These will not load using pfSense Restore and are here as a reference only. See GitHub #2282 for more info.

Tips for Setting Up pfSense Firewall Rules

Here are some general tips for setting up pfSense firewall rules:

  1. Create aliases for the repeated values (IPs and ports).
  2. pfSense is a stateful firewall, which means that you don’t need corresponding rules to allow incoming traffic in response to outgoing traffic (like you would in, e.g. iptables with --state ESTABLISHED,RELATED). pfSense does this for you automatically.
  3. You should create the rules on the interface where the traffic originates.
  4. Make sure you delete the default “allow all” rule on the LAN interface. Leave the “Anti-Lockout” rule enabled.
  5. Any traffic that is not explicitly passed is logged and dropped by default in pfSense, so you don’t need to add explicit rules (iptables LOGNDROP) for that.
  6. Since some of the rules are almost identical except for whether they allow traffic from the Application Server or the Monitor Server, you can use the “add a new rule based on this one” button to save time creating a copy of the rule on the other interface.
  7. If you are troubleshooting connectivity, the firewall logs can be very helpful. You can find them in the WebGUI in Status → System Logs → Firewall.

Keeping pfSense Up to Date

Periodically, the pfSense project maintainers release an update to the pfSense software running on your firewall. You will be notified by the appearance of text saying that there is a new version in the Version section of the “Status: Dashboard” page (the home page of the WebGUI).

Update available

If you see that an update is available, we recommend installing it. Most of these updates are for minor bugfixes, but occasionally they can contain important security fixes. You should keep apprised of updates yourself by checking the pfSense Blog posts with the “releases” tag.


Protip: Subscribe to the RSS feed.

To install the update, click the Download icon next to the update then click the “Confirm” button:

Firewall Update Confirmation

You will see a page with a progress bar while pfSense performs the upgrade:

Firewall Update Progress


This may take a while, so be patient!

Once it is complete, you will see a notification of successful upgrade:

Firewall Update Complete

[1]Tails screenshots were taken on Tails 3.0~beta4. Please make an issue on GitHub if you are using the most recent version of Tails and the interface is different from what you see here.

Abstract firewall rules

The pfSense instructions using the web interface can also be precisely described as follows:

  • Disable DHCP (in case the firewall is providing a DHCP server by default)
  • Disallow all traffic by default (inbound or outbound)
  • Allow UDP OSSEC (port 1514) from Application Server to Monitor Server
  • Allow TCP ossec agent auth (port 1515) from Application Server to Monitor Server
  • Allow TCP/UDP DNS from Application Server and Monitor Server to the IPs of known name servers
  • Allow UDP NTP from Application Server and Monitor Server to all
  • Allow TCP any port from Application Server and Monitor Server to all (this is needed for making connections to the Tor network)
  • Allow TCP 80/443 from Admin Workstation to all (in case there is a need to access the web interface of the firewall)
  • Allow TCP ssh from Admin Workstation to Application Server and Monitor Server
  • Allow TCP any port from Admin Workstation to all

This can be implemented with iptables, Cisco IOS etc. if you have the necessary expertise.